Implement Mounting Pins
NOTE: Parts shown are BARE-Co parts - original part numbers are shown for reference only.

ONLY BARE-Co PROVIDES:

  • Cold forged pins to 1 1/8"dia for consistent grain flow, maximum strength and superior surface finish.
    (Our competitors do not have the capability to cold form pins from 1 1/8" dia. Wire)
  • Large radius at fracture point (difficult to achieve in cold forging).
  • Guaranteed base material to min. specifications S1040 carbon steel.

FORGET ABOUT DRAWINGS!
JUST DETERMINE IMPLEMENT HOLE DIA. AND TRACTOR CATEGORY

  • All pins correct length to accept stay bars or next linkage category bush upgrade.
  • Various length stepped shoulders replaced by straight shank to increase strength and reduce your inventory. Stepped types available for 40 year old Ferguson tiller and mowers.
  • Only BARE-Co have invested in special thin wall nuts, to provide clearance for straight shank design on plow cross shafts etc.
STANDARD BOLT-IN IMPLEMENT MOUNTING PINS
Fits Frame 3/8" to 1 1/8" Thick
SHOULDER/SHANK DIA (IMPLEMENT HOLE DIA)
TRACTOR HITCH CATEGORY (PIN DIA)
PART No.

Replaces
Old Design
with 2 Nuts

3/4" UNF

CAT 1 =7/8"

B198

CAT 2 = 1 1/8"

B197

7/8" UNF

CAT 1 =7/8"

B200

CAT 1 =7/8"

B2406

CAT 2 = 1 1/8"

B202

CAT 3 = 1 7/16"

B2520

1" SAE
14TPI

CAT 1 = 7/8"

B101

CAT 2 = 1 1/8"

B102

CAT 3 = 1 7/16"

B2521

1 1/8" UNF

CAT 1 = 7/8"

B201

CAT 2 = 1 1/8"
B203

CAT 3 = 1 7/16"
B2522

WELD-IN AND NON-STANDARD LOWER IMPLEMENT MOUNTING PINS
NOTE: standard cold forged pins (B200 above / B215 etc below) are much CHEAPER than the pins below!

PART No

DESCRIPTION

Extra Long Thread Shank: "A" = 3"

 

B2406

CAT 1 Replaces
I.H.C. 802585R2

B2407

CAT 2 Replaces
I.H.C. 802586R2
B428
CAT 1
7/8" dia. thread.
Very OLD design without Forged Collar
Failure Point HERE if non adjusting collar nut is moved.
Replace with B200, B202
OR - B2406, B2407 if Long Thread Required
B429
CAT 2
1 1/8" dia. thread.

B199

Fits old FERGUSON
TILLER "A" = 5/8"
Replaces 646038MI
CAT 1 Pin
7/8" dia. shoulder

B2475

Fits MASSEY FERGUSON TILLER "A" =3/4"
Replaces 889440MI
CAT 1 Pin
7/8" dia. shoulder

B2951

Fits M.F. 532 MOWER
CAT 1 Pin
shoulder 1 1/8"dia x 2 3/8" long
Replaces
195531MI - 195532M1

 

B205

DUAL CAT 1-2 Fits
Frame Thickness
3/8" to 1"
Fits 1" hole drilling

 

B206

Fits 1 1/8" hole drilling

B210

Fits 7/8" drilling
A = 3 1/2" B = 2 1/8"

 

B214

Fits 1 1/8" drilling
A = 2" B =3 1/8"

B7214

Fits2" RHS
1 1/8" drilling
A = 2 1/8" B = 4 5/16"
NOTE: standard cold forged pins (B200 above / B215 etc below) are much CHEAPER than the pins above!

SLIP-IN LOWER IMPLEMENT MOUNTING PINS
STANDARD SINGLE CATEGORY PINS
PART No
TRACTOR LINKAGE CATEGORY (PIN DIA.)
USEABLE LENGTH
B215
CAT 1 (7/8" = 22mm)
4 1/8" = 105mm
B216
CAT 2 (1 1/8" = 28.6mm)
B2662
CAT 2 (1 1/8" = 28.6mm)
4 3/4" = 120mm
(includes handle)
B4216
5 1/8" = 130mm
B2517
CAT 3 (1 7/16" = 36.5mm)
5" = 127mm
8" = 203mm
B3517
CAT 3 (1 7/16" = 36.5mm)

DUAL CATEGORY LOWER PINS
PART No
APPLICATION
B100
Universal
Implement Mounting Pins